Bare Co PTO Shafts

"The most user Friendly PTO cover in the world"

The Ultimate in PTO Safety –Reusable, Easy Re-greasing, , Safe UV Resistant Hardwearing

MAKING THE FARM A SAFER PLACE

The Bare-Co PTO shaft guard is a unique guard that can be unclipped from its bearing point at the yoke end and moved back along the shaft for easy greasing of the crosses. The innovative design of the Bare-Co PTO guard allows the guard to be quickly pulled back to facilitate safe engagement of end yokes and regular joint maintenance.

STANDARD SHAFTS include SAFETY GUARD & 1 3/8 x 6 spline QUICK RELEASE YOKE BOTH ENDS 

NOTE: Reduce HP rating by 40% for severe conditions

16HP @ 540 rpm
26HP @ 1000 rpm

21HP @ 540 rpm
34HP @ 1000 rpm

35HP @ 540 rpm
56HP @ 1000 rpm

64HP @ 540 rpm
102HP @ 1000 rpm

106HP @ 540 rpm
170HP @ 1000 rpm


E4050  

Cross to Cross
Measurement

Overall 
Measurement

75-110cm

94-127cm

 

 

E4051 

Cross to Cross
Measurement

Overall
Measurement

90-145cm

110-163cm

 

E4052

Cross to Cross
Measurement

Overall
Measurement

45-64cm

66-84cm

 

 

E4053

Cross to Cross
Measurement

Overall
Measurement

75-110cm

97-130cm

 

 

 

E4054

Cross to Cross
Measurement

Overall
Measurement

100-160cm

119-180cm

 

 

 

 E4055

Cross to Cross
Measurement

Overall
Measurement

75-110cm

100-130cm

 

 

E4056

Cross to Cross
Measurement

Overall
Measurement

100-160cm

122-182cm

 

 

E4057

Cross to Cross
Measurement

Overall
Measurement

150-250cm

175-270cm

 

 

 

E4058

Cross to Cross
Measurement

Overall
Measurement

75-110cm

102-130cm

 

 

E4059

Cross to Cross
Measurement

Overall
Measurement

100-160cm

125-180cm

 

 

 

E4060

Cross to Cross
Measurement

Overall
Measurement

150-250cm

180-270cm

 

 

 E4061

Cross to Cross
Measurement

Overall
Measurement

100-160cm

130-180cm

 

 

E4062

Cross to Cross
Measurement

Overall
Measurement

150-250cm

185-270cm

Drive Shaft Cover -Small
Yoke Bearing Grove Diameter 32-53mm

Drive Shaft Cover -Large
Yoke Bearing Grove Diameter 53-80mm

E4063 LENGTH 1m-1.6m

E4063X15 LENGTH 1.5m-2.5m

E4064 LENGTH 1m-1.6m

E4064X15 LENGTH 1.5m-2.5m



How to choose the correct PTO shaft

1) Determine the engine HP rating and PTO speed of your tractor ( ie: 55hp, 540rpm )  NOTE: Reduce HP rating by 40% for severe conditions

2) Choose a driveshaft range which has a higher HP rating than your tractor (ie: Series 6, -64hp@540rpm)
NOTE: if your need is to run a light application like a fertiliser spreader then you probably don’t have to consider a higher HP shaft. Using a light weight Pto shaft will probably be your best bet.

3) Take 3 measurements of the distance between PTO shaft protruding from rear of tractor and the gearbox shaft on the implement. (ie: overall distance to where end of PTO shaft sleeve would sit) 
a) Measure with implement fully raised
b) Measure with implement at mid height
c) Measure with implement flat on the ground

4) Note the shortest and Longest measurements, this is your working range.

5) Select a drive shaft that either fits this working range or is longer than the working range so it can be shortened down.

 

 

The Ultimate in PTO Safety –Reusable, Easy Re-greasing, Safe UV Resistant Hardwearing.

MAKING THE FARM A SAFER PLACE

The Bare-Co PTO shaft guard is a unique guard that can be unclipped from its bearing point at the yoke end and moved back along the shaft for easy greasing of the crosses. The innovative design of the Bare-Co PTO guard allows the guard to be quickly pulled back to facilitate safe engagement of end yokes and regular joint maintenance.

 

crt card image
farmlands logo
mastercard logo
visa logo
RD1 logo
100% NZ logo
windcave logo